This forum is now closed and archived but the many helpful kiln-related topics are still available to view.
Please feel free to read through the archive or visit www.wagnermeters.com
for more detail about our wide array of moisture measurement solutions.

Author Topic: Surface Check from Old Logs  (Read 9263 times)

Offline Craig Jensen

  • Newbie
  • *
  • Posts: 38
    • View Profile
Surface Check from Old Logs
« on: June 04, 2012, 01:36:22 PM »
We are getting more surface check than usual right now on our DF and Larch. The logs are 9 - 12 months old.  While the checks are not there on the green product, my kiln handbook says that surface checks happen early in the schedule when the relative humidity is too low.  I am attributing these checks to old logs because the drying times have reduced from normal by about 25%, indicating a dryer log going in, and lower wet bulb temperature than normal during the first part of the schedule.

Does this make sense to anyone?  Any ideas?  Has anyone heard of using steam spray early in the schedule to avoid this?

Craig J.

Offline Kevin Bethel

  • Newbie
  • *
  • Posts: 4
    • View Profile
Re: Surface Check from Old Logs
« Reply #1 on: June 05, 2012, 10:16:33 AM »
try activating your spray early  I activate mine within the first hour lower your depression and reduce fan reversal I use every hour for old logs just tested this on some old DF logs that were decked last Oct and increased recovery by 2-3%  not a drastic inprovement but every little bit helps in this economy   

Offline Craig Jensen

  • Newbie
  • *
  • Posts: 38
    • View Profile
Re: Surface Check from Old Logs
« Reply #2 on: June 05, 2012, 12:39:07 PM »
Thanks Kevin,
I'll try that.  Our fan reversals are every half hour for first 2, then every hour after, but had not tried steam spray yet.

Have you tried it on Larch?

CJ

Offline Kevin Bethel

  • Newbie
  • *
  • Posts: 4
    • View Profile
Re: Surface Check from Old Logs
« Reply #3 on: June 06, 2012, 06:27:40 AM »
No Craig, we don't cut much Larch anymore here.  In the last year we've only ran 1 day of Larch.  We ship most of it to Chilco or you.

Offline MichaelM

  • Forum Expert
  • Kiln Drying Enthusiest
  • *****
  • Posts: 98
    • View Profile
Re: Surface Check from Old Logs
« Reply #4 on: June 06, 2012, 10:33:38 AM »
"try activating your spray early  I activate mine within the first hour lower your depression and reduce fan reversal I use every hour"

This sounded like good advice.  If you are now using half hour reversals like I think I saw in a later post, I would go to an hour because the vents open when you reverse the fans and this will increase the need for spray.

Also, make sure the depression is held on the way up in temperature.  You might need to ramp up a little more slowly or get halfway to temperature and hold the temperature setting steady for an hour or two to let the wood warm up.

Offline Craig Jensen

  • Newbie
  • *
  • Posts: 38
    • View Profile
Re: Surface Check from Old Logs
« Reply #5 on: June 08, 2012, 09:45:56 PM »
Thanks guys.

Will try this.  Will let you know how it turns out.

Craig J.

 


Search


* Forum Experts

MichaelM MichaelM
Forum Expert
TimothyD TimothyD
Forum Expert
PhilM PhilM
Forum Expert
StavrosA StavrosA
Forum Expert

* Subscribe to Newsletter

* Upcoming Events

Sorry! There are no calendar events available at the moment.
\
SimplePortal 2.3.6 © 2008-2014, SimplePortal